Enceinte en Kit Visaton ARIA 2
[5946] Avis/Critiques KIT DIY, prix affiché pour les accessoires de 1 enceinte acoustique appolito.
Enceinte acoustique appolito en kit, le kit comprend les haut-parleurs, les câbles, les matériaux d'amortissement, les vis de fixation, les borniers de connexions, filtres passifs, events de décompression...
Enceinte 2 voies de type appolito équipée de 2 haut-parleurs basse-medium Visaton TI100 et d'un tweeter Visaton G 20 SC.
Cette enceinte peut être utilisée en hifi comme en home cinéma pour faire office d'enceinte centrale performante.
Characteristics and sound properties
The ARIA 2 is a small-sized 2-band shelf-top speaker system that uses two TI 100 8 Ohm high-end mid-bass units and the G 20 SC 8 Ohm dome tweeter. The unit is equally well suited to life as a satellite in a straightforward stereo system or for use in a multichannel set-up. It can be combined with larger speakers such as the VOX 200 where it takes over the centre or effect role or a full set of them can be used to cover all channels. The lower limiting frequency is at 75 Hz, i.e. deep-bass should be left to an active subwoofer and the satellites will need protecting with a high-pass section or, in multichannel systems, they should be run in small mode.
If the speakers are positioned right by the wall or in a shelving unit, the bass reflex tube will be partly damped or completely stifled, which can compensate for excessively boosted bass.
Extract from HobbyHiFi
"Verdict: By making the universally applicable Aria 2 available, VISATON has enriched the existence of DIY speaker builders by a considerable amount. Even with a stand-alone compact speaker, the Aria 2 puts on a remarkably good show but in conjunction with a suitable bass driver it will wipe the board. This makes it eminently suitable for a step-by-step approach. A user could start by building a couple of Aria 2's, later on add a subwoofer and, after that, add a third Aria 2 as a centre speaker to make an entry into the world of surround systems a suitable Aria dipole speaker for the surround channels is also to be found in the VISATON catalogue."
Technical Data:
Rated power 80 W
Maximum power 120 W
Nominal impedance Z 4 Ohm
Frequency response 75 - 30000 Hz
Mean sound pressure level 86 dB (1 W/1 m)
Cut-off frequency 2500 Hz
Principle of Housing Bassreflex
Net volume 8 l
Outer dimension height 396 mm
Outer dimension width 160 mm
Outer dimension depth 210 mm
CONSTRUCTION
The cabinet body uses 16 mm boards. First of all, cut the holes in the boards and apply the bevels. This can be done using an electric jigsaw or hand-held circular saw set to the required angle. Once the cabinet has been completed, apply the milling work for the loudspeaker. Finally, fit the cones.
Since the cabinets are relatively small, it is hardly possible to mount the crossover inside the housing. It can, however, simply be wrapped in damping material and placed inside the speaker if the rear wall is not removable.
Inner damping
The damping material is loosely arranged in the cabinet.
Component parts list for 1 box
The kit includes all necessary components (see list below). Cabinet parts are not included.
Tweeter: G 20 SC 8 Ohm 1 piece
Woofer: TI 100 8 Ohm 2 piece
Crossover: Crossover ARIA 2
Bass reflex tube: BR 6.8 (full length) 2 pieces
Terminal: ST 77 1 piece
Damping material: 0.5 bag
Wood screws: 3,5 x 19 mm 8 pieces
Countersunk screws: 3,5 x 25 mm 8 pieces
Cable: 2 x 1,5 mm² 1 m
................
Cabinet parts list for 1 box
Parts Size (mm) Quantity
Material: 16 mm chipboard or MDF
Front and rear panel 396 x 160 2
Side panel 396 x 178 2
Top and bottom panel 178 x 128 2
Plan de fabrication pour enceinte Visaton ARIA 2 :
Schéma du filtre passif de l'enceinte Visaton ARIA 2 en kit :
|
