Enceinte en Kit Visaton COUPLET LIGHT
[5928] Avis/Critiques KIT DIY, prix affiché pour les accessoires de 2 enceintes
acoustiques.
Paire d'enceintes acoustiques en kit, le kit comprend les
haut-parleurs, les câbles, les matériaux d'amortissement, les vis de fixation,
les borniers de connexions, filtres passifs...
Paire d'enceintes 2 voies équipées unitairement de
deux medium-woofers Visaton W130S et d'un tweeter Visaton
G20SC.
Characteristics and sound properties
The COUPLET LIGHT is
a compact D Appolito configuration shelf speaker. It can be used as a shelf-top
speaker or mounted on free-standing supports. In contrast to the original
COUPLET, this system uses two W 130 S 8 OHM as woofers. The tweeter and the
cabinet design with its flow-optimised BR 25.50 bass reflex tube have been taken
over unchanged.
The result is a speaker that maintains its linear characteristics right
across the frequency range. Due to the well balanced medium range, the fine
details of music reproduction, in particular, comes across particularly clearly.
The excellent omnidirectional sound distribution creates a particularly
room-filling music reproduction and clear location of each individual instrument
or voice. The lowest-range bass comes across equally powerfully. In short, the
COUPLET LIGHT is a speaker that is really good fun.
Technical Data:
Rated power 100 W
Maximum power 160
W
Nominal impedance Z 4 Ohm
Frequency response 40 - 30000 Hz
Mean
sound pressure level 83 dB
(1 W/1 m)
Cut-off frequency 3500 Hz
Principle of Housing Bassreflex
Net volume 25 l
Outer dimension
height 460 mm
Outer dimension width 235 mm
Outer dimension depth 350
mm
Plan de fabrication pour enceinte Visaton COUPLET LIGHT :
CONSTRUCTION
All the cabinet panels are cut from 19 mm
chipboard or medium density fibreboard, butt-jointed and glued. The chamfers on
the baffle can be applied with a power jig or circular saw set to 45° or applied
later using an orbital sander.
Next, cut out the openings for the drivers,
the bass reflex tube and the terminals.
Due to the small size of the cut-outs in the baffle, it is difficult to mount
the crossover inside the speaker cabinet. It would be possible to make the base
removable. However, it is easier to wrap the crossover in damping material and
place it through the lower cut-out in the baffle on the floor of the cabinet.
When you begin fitting the drivers, start with the bass reflex tube. In order to
be able to get the inner trumpet flange through the opening for the upper
subwoofer it will be necessary to carefully remove about 5 mm from both sides of
the flange.
Inner damping
The damping material is loosely arranged
below the bass reflex tube in the cabinet in such a way that the area around the
vent remains free.
Component parts list for 1 box
The kit includes all the
components listed here but not the cabinet.
Tweeter: G 20 SC 8 Ohm
1 piece
Woofer: W 130 S 8 Ohm 2 pieces
Crossover: Crossover COUPLET
LIGHT
Bass reflex tube: BR 25.50 (full length) 1 piece
Terminal:
ST 77 1 piece
Damping material: Polyester wool 1 bag
Wood screws: 3,5 x
19 mm 4 pieces
Countersunk screws: 3,5 x 25 mm 18 pieces
Cable: 2x 1,5
mm² 1,5 m
................
Cabinet parts list for 1 box
Parts Size (mm) Quantity
Material: 19 mm MDF or chipboard
Front, rear panel 460 x 235 2
Side panels 460 x 312 2
Top, bottom panel 197 x 312 2
Schéma du filtre passif de l'enceinte Visaton COUPLET
LIGHT :
|
