Amplificateur numérique Powersoft DIGAM K8
[DIGAM K8] Avis/Critiques Features
Advanced switch-mode worldwide operating power supply technology for high performance and compact size
Power Factor Correction PFC for extremely low mains consumption and extremely wide mains operating range
Variable speed fan for low noise
Low Inrush Limiting reduces AC inrush current, removing the need for expensive power sequencers
XLR female / 6.3mm Jack Neutrik style input connectors with link capability
Built-in defeatable Clip limiters for each channel
LCD matrix interactive display
Digital gain-attenuator control
User selectable maximum output power for each channel
User selectable maximum mains current draw
Comprehensive-user friendly front panel display menu
Fully protected circuitry design including DC, infrasonic, high frequency, thermal overload and short circuit
Temperature forecast with LCD traced historical behaviour
Downloadable log file of functional fault events with time related trace
Load impedance measurement / display for each channel
Output power measurements / display for each channel
Mains voltage and current measurements / display
Defeatable gate selection for each channel
Gain/sensitivity user selection capability
Hardware monitor available for fast local diagnostic
Fixed frequency switchmode output stage for high grade sound accuracy
Compact size - all models only 1 RU for reduced rack cost and space
Light weight - all models only 12 kg (26 pounds) for easier racking and shipping
Built in Remote Control ( RS 485 interface ) for full diagnostic, operational setting and system monitoring
Smart Card settings , parameters and upgrades functionality
Lockable set-up by user selectable access key code
DSP option capability
Ethernet option capability
Protections circuitry
DC protection: protects against infrasonic signals
VHF protection: protects the loudspeakers against strong very high frequency non-musical signals above the audible range.
Thermal protection: prevents the amplifier from being overheated. The protection indicators on the front panel are switched on, as a warning, before the protection process is initiated.
AC protection: shuts down the power supply if the line voltage is outside the operating voltage.
Clip limiter: prevents severely clipped waveforms from reaching the loudspeakers, whilst maintaining full peak power.
General
Power requirements AC:95 - 265V (50/60Hz)
Power factor cos(fi) More than 0.95 from 200 W to full power
Operating temperature O°C / + 45° C
Weigth 12 Kg
External dimensions Standard rack 19", 1 unit ( H ), 475 mm ( D )
Consumption average 2300 VA ( K10 @ 1/8 maximum output power)
Audio section
Bandwith ( 1 W, 8 ohm ) 5Hz – 30KHz
Damping factor ( 8 ohm ) >5000 (20Hz-200Hz)
Slew rate ( 8 ohm ) 50V /uS ( input filter bypassed )
S/ N ratio A-Weighted 20Hz-20KHz > 112dB (K20), >110dB (K10), >109dB (K8), >108dB (K6),
Distortion THD : Max < 0.5% From 0.1W to full power (tipically < 0.05%)
Intermodulation SMPTE Max < 0.5% From 0.1W to full power (tipically < 0.05%)
Intermodulation DIM 30 Max < 0.5% From 0.1W to full power (tipically < 0.05%)
Input Balanced to ground , XLR female combo jack 6.3 mm
Impedance 10 Kohm each leg, electronically balanced to ground
Gain/ Sensitivity 26dB; 29dB; 32dB; 35dB user selectable
Output High current Neutrik 4-pole Speakon connectors ( pins 1+ 2+ paralleled, 1-2-paralleled)
Puissances délivrées :
2 Ohm dual : 4800 Watts
4 Ohm dual : 3000 Watts
8 Ohm dual : 1500 Watts
4 Ohm bridge : 96000 Watts
8 Ohm bridge : 6000 Watts
16 Ohm bridge : 3000 Watts
|
