ToutleHautParleur.com

PHL 3860

Midrange transducer dedicated to the reproduction of 120-3000 Hz frequencies. Equiped with a progressive wave diaphragm for precise transcription of the mid-range band. For hor loaded application.

Power handling capacity : 250 W AES
Reference efficiency (1W @ 1m) : 101 dB SPL
SPL max (continous) : 121 dB SPL
Usable frequency range : 120 to 3000 Hz
Environmental withstanding : Outdoor

TYPICAL CHARACTERISTICS
Rated impedance	Z	W	8
Half space sensitivity (1W@1m)	-	dB SPL	101
Usable freq. range	-	Hz	120-3000
Power handling capacity (AES)	-	W	250
Max Sound Pressure Level	SPLmax	dB SPL	121
Min. impedance modulus	Zmin	W@Hz	5.3@410
Voice-coil inductance @ 1kHz	Le_1k	mH	1,04
Voice-coil inductance @ 10kHz	Le_10k	mH	0,56
BL product	BL	N/A	18,80
Moving mass	Mms	kg	0,033
THIELE-SMALL PARAMETERS: TYPICAL (QC LIMITS)
Resonance frequency	Fs	Hz	86(±17)
DC Resistance	Re	W	4.6(±0.5)
Mechanical quality factor	Qms	1	2,5
Electrical quality factor	Qes	1	0,23
Total quality factor	Qts	1	0,21
Mechanical suspension compliance	Cms	10^-6.m/N	105
Effective piston area	Sd	m²	0,0377
Equivalent Cas air load	Vas	m³	0,021
Max linear excursion	Xmax	±mm	2,0
Linear displacement volume	Vd	10^-3.m³	0,075
Reference efficiency	h₀	%	5,5
Unity load volume	Vas.Qts²	10^-3.m³	0,9
ABSOLUTE MAXIMUM RATINGS
Short term max. input voltage	Vmax	V	100
Max.excursion before damage	Xdam	±mm	4,0
Ambient operating temperature	Ta	°C	-10 to +50
Storage temperature	-	°C	-20 to +70
Environemental withstanding Q	-	-	Outdoor
APPLICATION INFORMATION
Air volume occupied by the driver	-	10^-3.m³	2,0
Speaker net mass		kg	8,240
Recommended reflex box	Vb/Fb	Lts/Hz	4-6L Sealed

TangBand W3-316B

Fullrange frequency response
Die cast basket
PPM cone with santoprene surround
CCAW with kpaton voice coil
Vented basket under spider

Specifications :

Diaphragm material : PPM
Surround material : Santoprene
Nominal impedance : 8 ohms
DC resistance : 6.6 ohms
Sensivity : 88 dB/1w/1m
Frequency response : 100 - 20000 Hz
Free air resonance (Fs) : 100 Hz
Voice coil diameter : 20.4 mm
Air gap height : 4 mm
Rated power input : 12 w
Maximum power input : 25 w
Force factor (BL) : 4.13 T.m
Magnet material : Ferrite (227g->8oz)
Moving mass (Mms) : 2 g
Ferrofluid Enhanced : No
Suspension compliance (Cms) : 1302 uMN-1
Effective piston area (Sd) : 32 cm²
Levc : 0.073 mH
Zo : 80.00 ohms
Xmax : 0.1.2 mm
Vas : 1.89 L
Qts : 0.44
Qms : 5.62
Qes : 0.48
Weight (nacked) : 0.57 kg

TangBand W3-926SD

Fullrange frequency response
Stamped steel basket
Aluminium phase plug
polypropylen cone with santoprene surround
Neodymium magnet design
Magnetically shielded

Specifications :

Diaphragm material : Black PP
Surround material : Pulux
Nominal impedance : 8 ohms
DC resistance : 6.0 ohms
Sensivity : 85 dB/1w/1m
Frequency response : 110 - 20000 Hz
Free air resonance (Fs) : 110 Hz
Voice coil diameter : 20.4 mm
Air gap height : 4 mm
Rated power input : 12 w
Maximum power input : 25 w
Force factor (BL) :3.56 T.m
Magnet material : Neodymium
Moving mass (Mms) : 2 g
Ferrofluid Enhanced : No
Suspension compliance (Cms) : 1269 uMN-1
Effective piston area (Sd) : 32 cm²
Levc : 0.20 mH
Zo : 61.30 ohms
Xmax : 0.75 mm
Vas : 1.85 L
Qts : 0.51
Qms : 5.18
Qes : 0.56
Weight (nacked) : 0.23 kg

TangBand W8-670C

Long Throw high power loading design
Extremely linear excursion design
Paper cone with big roll
Vented pole piece
Stamped steel basket
Suitable for subwoofer application

Specifications :

Diaphragm material : Paper
Surround material : Foam
Nominal impedance : 8 ohms
DC resistance : 6.5 ohms
Sensivity : 87 dB/1w/1m
Frequency response : 37 - 800 Hz
Free air resonance (Fs) : 40 Hz
Voice coil diameter : 38 mm
Air gap height : 8 mm
Rated power input : 80 w
Maximum power input : 150 w
Force factor (BL) : 13 T.m
Magnet material : Ferrite (808g->28.5oz)
Moving mass (Mms) : 45 g
Ferrofluid Enhanced : No
Suspension compliance (Cms) : 379.27 uMN-1
Effective piston area (Sd) : 220 cm²
Levc : 0.715 mH
Zo : 90.88 ohms
Xmax : 7 mm
Vas : 25.68 L
Qts : 0.37
Qms : 3.94
Qes : 0.41
Weight (nacked) : 3.03 kg

TangBand W3-871B

Fullrange frequency response
Round stamping steel basket
Aluminium phase plug
Paper cone with santoprene surround
Magnetically shielded
Aluminium phase plug cooling

Specifications :

Diaphragm material : Silver paper
Surround material : Santoprene
Nominal impedance : 8 ohms
DC resistance : 6.6 ohms
Sensivity : 87 dB/1w/1m
Frequency response : 110 - 20000 Hz
Free air resonance (Fs) : 110 Hz
Voice coil diameter : 18 mm
Air gap height : 6 mm
Rated power input : 12 w
Maximum power input : 25 w
Force factor (BL) : 3.51 T.m
Magnet material : Ferrite (125g->4.4oz)
Moving mass (Mms) : 2.0 g
Ferrofluid Enhanced : No
Suspension compliance (Cms) : 1133 uMN-1
Effective piston area (Sd) : 32 cm²
Levc : 0.75 mH
Zo : 38 ohms
Xmax : 0.5 mm
Vas : 1.65 L
Qts : 0.59
Qms : 3.40
Qes : 0.71
Weight (nacked) : 0.65 kg

TangBand W5-704D

Twin roll rubber surround
Extremely linear excursion design
PPM cone with twin roll shape rubber surround
DIe cast basket, PPM phase plug
Intended for bass reflex enclosures
Vented pole piece
Durable conex spider

Specifications :

Diaphragm material : PPM
Surround material : Twin Roll Rubber
Nominal impedance : 8 ohms
DC resistance : 6 ohms
Sensivity : 88 dB/1w/1m
Frequency response : 55 - 9000 Hz
Free air resonance (Fs) : 55 Hz
Voice coil diameter : 25 mm (1.0 inch)
Air gap height : 6 mm
Rated power input : 28 w
Maximum power input : 56 w
Force factor (BL) : 6.17 T.m
Magnet material : Ferrite (409g->14.4 oz)
Moving mass (Mms) : 7.98 g
Ferrofluid Enhanced : No
Suspension compliance (Cms) : 922.088 uMN-1
Effective piston area (Sd) : 94 cm²
Levc : 0.063 mH
Zo : 33 ohms
Xmax : 3.3 mm
Vas : 11.57 L
Qts : 0.38
Qms : 2.07
Qes : 0.46
Weight (nacked) : 1.36 kg

TangBand W4-1052SDF

Fullrange design
Structured polypropylen cone with wide range temperature rubber surround, stable Fo
Stamped steel basket
Good for home theater, multimedia, car application

Specifications :

Diaphragm material : Structured pp
Surround material : Rubber
Nominal impedance : 4 ohms
DC resistance : 3.8 ohms
Sensivity : 88 dB/1w/1m
Frequency response : 70 - 17000 Hz
Free air resonance (Fs) : 70 Hz
Voice coil diameter : 25.4 mm (1.0 inch)
Air gap height : 2.5 mm
Rated power input : 20 w
Maximum power input : 40 w
Force factor (BL) : 4.10 T.m
Magnet material : Ferrite (305g->10.80 oz)
Moving mass (Mms) : 4.61 g
Ferrofluid Enhanced : No
Suspension compliance (Cms) : 1128 uMN-1
Effective piston area (Sd) : 57 cm²
Levc : 0.0077 mH
Zo : 45 ohms
Xmax : 2.6 mm
Vas : 5.21 L
Qts : 0.42
Qms : 4.80
Qes : 0.46
Weight (nacked) : 0.605 kg

AB Sound PE-0.61X15-TN

Grille plastique rigide noire pour façade d'enceinte. Bon compromis entre le tissu acoustique et la grille acier.

Matériau: Nylon rigide
Couleur: noir
Largeur: 0.61 mètre
Masse: 400 gr/mètre.

Produit vendu au mètre, prix affiché pour un mètre.

Exemple si vous commandez deux mètres vous recevrez un morceau de 0.61m x 2.0m.

Longueur maximale livrable : 15 mètres (correspondant à un morceau de 0.61m x 15m livré en une fois).

AB Sound PE-1.45X1500-TN

Tissu acoustique en nylon pour façade d'enceinte ou façade d'ampli guitare. Texture vintage noire, très robuste et transparent acoustiquement.

Matériau: Nylon souple
Couleur: noir avec couture blanche sur les bords
Largeur: 1.45 mètre
Masse: 330 gr/mètre.

Produit vendu au mètre, prix affiché pour un mètre.

Exemple si vous commandez deux mètres vous recevrez un morceau de 1.45m x 2.0m.

Longueur maximale livrable : 25 mètres (correspondant à un morceau de 1.45m x 20m livré en une fois).

TangBand W2-803SM

- FULL RANGE DESIGN
- ABS BASKET, MAGNETICALLY SHIELDED
- SILVER PPM CONE WITH R SHAPE TPR SURROUND
- NEODYNIUM MAGNET DESIGN
- GOOD FOR CAR, HOME THEATER, MULTIMEDIA APPLICATION
- SPECIAL ALUMINUM PHASE PLUG TO PROVIDE WIDER DISPERSION AND HEAT SINK

Specifications :

DIAPHRAGM MTL Silver PPM
SURROUND MTL TPR
NOMINAL IMPEDANCE 4 ohm
DCR IMPEDANCE 3.6 ohm
SENSITIVITY 1W/1m 85 dB
FREQUENCY RESPONSE 160-20K Hz
FREE AIR RESONANCE 160 Hz
VOICE COIL DIAMETER 20.4 mm
AIR GAP HEIGHT 3.0 mm
RATED POWER INPUT 8 W
MAXIMUM POWER INPUT 16 W
FORCE FACTOR, BL 2.69 TM
MAGNET WEIGHT (oz) Neodymium
MOVING MASS 0.87 g
FERRO FLUID ENHANCED No
SUSPENSION COMPL. 1051 uMN-1
EFFEC.PISTON AREA 0.0013 M2
Levc 0.04 mH
Zo 33 ohm
X-max 0.85 mm
Vas 0.25 Litr.
Qts 0.40
Qms 3.56
Qes 0.46

TangBand 25-1933S

- LOW FO=600Hz
- CLEAR, HIGH LOSS MATERIAL COATED, SOFT DOME - DIAPHRAGM
- SHORT RING AND BACK CHAMBER DESIGN
- VERY LOW THD (2nd AND 3rd HARMONIC DISTORTION)
- NEO MAGNET
- FERROFLUID COOLED
- MAGNETIC SHIELDED

Specifications :

DIAPHRAGM MTL Fabric
SURROUND MTL N/A
NOMINAL IMPEDANCE 6 ohm
DCR IMPEDANCE 5 ohm
SENSITIVITY 1W/1m 90 dB
FREQUENCY RESPONSE 600-20K Hz
FREE AIR RESONANCE 600 Hz
VOICE COIL DIAMETER 25.4 mm
AIR GAP HEIGHT 2 mm
RATED POWER INPUT 8 W
MAXIMUM POWER INPUT 80 W
FORCE FACTOR, BL N/A
MAGNET WEIGHT (oz) Neodymium
MOVING MASS N/A
FERROFLUID ENHANCED Yes

TangBand 25-1744S

- CERAMIC DIAPHRAGM WITH FABRIC SURROUND
- SHORT RING AND BACK CHAMBER DESIGN, Fo OF 700Hz
- LOW 2nd & 3rd DISTORTION (LOW THD)
- EXCELLENT OFF-AXIS DISPERSION
- NEODYMIUM MAGNET
- FREQUENCY RESPONSE OF 700Hz~30KHz
- FERROFLUID COOLED
- MAGNETIC SHILDED

Specifications :

DIAPHRAGM MTL Ceramic
SURROUND MTL Fabric
NOMINAL IMPEDANCE 6 ohm
DCR IMPEDANCE 5 ohm
SENSITIVITY 1W/1m 90 dB
FREQUENCY RESPONSE 700Hz-30K Hz
FREE AIR RESONANCE 700 Hz
VOICE COIL DIAMETER 25.4 mm
AIR GAP HEIGHT 2 mm
RATED POWER INPUT 8 W
MAXIMUM POWER INPUT 80 W
FORCE FACTOR, BL N/A
MAGNET WEIGHT (oz) Neodymium
MOVING MASS N/A
FERROFLUID ENHANCED Yes
Levc 0.003 mH
Zo 9 ohm

TangBand W3-881SJ

- Neodymium magnet design
- Full range frequency response
- Die cast basket
- PPEM cone with santoprene surround
- Magnetically shielded

Specifications :

Diaphragm material : Paper
Surround material : Rubber
Nominal impedance : 8 ohms
DC resistance : 6.8 ohms
Sensivity : 89 dB/1w/1m
Frequency response : 75 - 20000 Hz
Free air resonance (Fs) : 75 Hz
Voice coil diameter : 25.4 mm (1.0 inch)
Air gap height : 10 mm
Rated power input : 25 w
Maximum power input : 50 w
Force factor (BL) : 4.7 T.m
Magnet material : Neodymium
Moving mass (Mms) : 3.49 g
Ferrofluid Enhanced : No
Suspension compliance (Cms) : 1391 uMN-1
Effective piston area (Sd) : 57 cm²
Levc : 0.013 mH
Zo : 28 ohms
Xmax : 3.0 mm
Vas : 6.41 L
Qts : 0.35
Qms : 1.29
Qes : 0.49
Weight (nacked) : 0.6 kg

TangBand W5-1685

HUGE FERRITE MAGNET, UNDER HUNG MOTOR DESIGN
SHORT RING ON POLE PIECE, VC=38mm
VERY LOW 2nd AND 3rd DISTORTION
LONG THROW, HIGH POWER LOADING, Xmax=6mm
NATURALLY HIGH FREQUENCY ROLL OFF, GOOD FOR CROSSOVER DESIGN

Specifications :

DIAPHRAGM MTL Paper
SURROUND MTL Rubber
NOMINAL IMPEDANCE 4 ohm
DCR IMPEDANCE 3.4 ohm
SENSITIVITY 1W/1m 82 dB
FREQUENCY RESPONSE 45-1.5K Hz
FREE AIR RESONANCE 45 Hz
VOICE COIL DIAMETER 32 mm
AIR GAP HEIGHT 5 mm
RATED POWER INPUT 40 W
MAXIMUM POWER INPUT 80 W
FORCE FACTOR, BL 6.51 TM
MAGNET WEIGHT (oz) Neodymium
MOVING MASS 24.95 g
FERRO FLUID ENHANCED No
SUSPENSION COMPL. 478.7 uMN-1
EFFEC.PISTON AREA 0.0094 m2
Levc 25 mH
Zo 36 ohm
X-max 9.25 mm
Vas 6.01 Litr.
Qts 0.48
Qms 2.83
Qes 0.58

TangBand W5-1138SM

LONG-THROW HIGH-POWER LOADING DESIGN( X-max=9.25mm)
PAPER CONE WITH BIG ROLL, LESS DAMPING RUBBER SURROUND
VENTED POLE PIECE
STAMPING STEEL BASKET
SUITABLE FOR SUBWOOFER APPLICATION

Specifications :

Fountek NeoCD3.0

- Strong Neodymium magnet
- 3 inch enforced sandwich diaphragm
- Build-in impedance convertor
- Low distortion, very fast transition

Specifications :
Sensitivity 93dB/1m/2.83v
Power handling 17W nominal,40W max
Frequency range 1,400-40,000Hz
Nominal impedance 7 ohm
DCR 0.02 ohm
Ribbon dimension 8mmX60mmX0.015mm
Effective ribbon area 480 square millimeter
Ribbon weight 18 milligram
Gap flux 0.6 Telsa average
Gap height 3 millimeter
Recommend cut frequency 3,000Hz with 3-order
Net.Weight 650 gram

Fountek NeoX3.0

- Founteks 3-rd generation ribbon driver technology
- 12mm width enforced sandwich ribbon diaphragm
- Higher power handling, lower distortion, very fast transition
- Strong Neodymium magnet
- Built-in impedance convertor

Specifications :
Sensitivity 95dB/1M/2V
Power handling 30W nominal, 50W max
Frequency range 1,200-40,000Hz
Nominal impedance 8 ohm
DCR 0.02 ohm
Ribbon dimension 12mmX80mmX0.015mm
Effective ribbon area 960 square millimeter
Ribbon weight 36 milligram
Gap flux 0.4 Telsa average
Gap height 13 millimeter
recommend cut frequency 2,000Hz with -12dB
Net. Weight 1015 gram

Fountek NeoX2.0

Specifications :
Sensitivity 94dB/1M/2V
Power handling 25W nominal, 43W max
Frequency range 1,200-40,000Hz
Nominal impedance 8 ohm
DCR 0.02 ohm
Ribbon dimension 12mmX60mmX0.015mm
Effective ribbon area 720 square millimeter
Ribbon weight 27 milligram
Gap flux 0.4 Telsa average
Gap height 13 millimeter
recommend cut frequency 2,500Hz with -12dB
Net. Weight 750 gram

Fountek NeoX1.0

Specifications :
Sensitivity 92dB/1M/2V
Power handling 20W nominal, 38W max
Frequency range 1,200-40,000Hz
Nominal impedance 8 ohm
DCR 0.02 ohm
Ribbon dimension 12mmX45mmX0.015mm
Effective ribbon area 720 square millimeter
Ribbon weight 20 milligram
Gap flux 0.4 Telsa average
Gap height 13 millimeter
recommend cut frequency 2,500Hz with -12dB
Net. Weight 630 gram

Fountek FR135EX

Haut-parleur de large bande 13 cm avec saladier moulé et système magnétique neodymium, large excursion de l'équipage mobile, très faible distorsion, Fs assez basse, bobine 32 mm.

Specifications :
Overall dimension : D146 x 73 mm
Net weight : 0.98 kg
Nominal power handling : 40 W RMS
Nominal impedance : 8 ohm
Sensivity : 85.1 dB/1w/1m
Frequency response : 50 - 26000 Hz
Fs :61.5 Hz

Voice coil :
Diameter : 32 mm
Height : 4 mm
Former : Black Aluminium
Wire : Copper ribbon
Number of layers : 1
DC resistance : 6.0 ohm

Magnet system :
Type : Neodymium
Gap height : 14 mm
B Flux density : 0.88 Tesla
Bl product : 5.027 Tm
Max linear excursion : +/- 5.0 mm

T/S parameters :
Cms : 0.887 mm/N
Sd : 70.50 cm²
VAS : 6.263 L
Mmd : 7.205 gr
Mms : 7.546 gr
Qms : 1.709
Qes : 0.692
Qts : 0.493

Fountek FW146

Haut-parleur de grave/médium 13 cm avec saladier moulé et membrane aluminium, ogive de dispersion (phase plug) en aluminium également, très faible distorsion, bobine 36 mm.

Specifications :
Overall dimension : D146 x 73 mm
Net weight : 1.265 kg
Nominal power handling : 35 W RMS
Nominal impedance : 8 ohm
Sensivity : 86.1 dB/1w/1m
Frequency response : 45 - 4000 Hz
Fs : 50 Hz

Voice coil :
Diameter : 26 mm
Height : 13 mm
Former : Black Aluminium
Wire : Copper ribbon
Number of layers : 2
DC resistance : 6.0 ohm

Magnet system :
Type : Ferrite
Gap height : 5.8 mm
B Flux density : 1 Tesla
Bl product : 6.065 Tm
Max linear excursion : +/- 3.6 mm

T/S parameters :
Cms : 1.142 mm/N
Sd : 77.61 cm²
VAS : 9.8 L
Mmd : 8.543 gr
Mms : 8.936 gr
Qms : 3.508
Qes : 0.456
Qts : 0.404

Fountek FW168

Haut-parleur de grave/médium 16 cm avec saladier moulé et membrane aluminium, ogive de dispersion (phase plug) en aluminium également, très faible distorsion, bobine 36 mm.

Specifications :
Overall dimension : D168 x 79.5 mm
Net weight : 1.76 kg
Nominal power handling : 50 W RMS
Nominal impedance : 8 ohm
Sensivity : 87.3 dB/1w/1m
Frequency response : 40 - 4000 Hz
Fs : 45 Hz

Voice coil :
Diameter : 36 mm
Height : 15 mm
Former : Black Aluminium
Wire : Copper round
Number of layers : 2
DC resistance : 7.2 ohm

Magnet system :
Type : Ferrite
Gap height : 5.8 mm
B Flux density : 1 Tesla
Bl product : 8.2 Tm
Max linear excursion : +/- 4.6 mm

T/S parameters :
Cms : 0.821 mm/N
Sd : 119 cm²
VAS : 16.5 L
Mmd : 13.955 gr
Mms : 14.7 gr
Qms : 3.246
Qes : 0.452
Qts : 0.397

Fountek FE85

Haut-parleur 3 pouce large bande, très bon rapport qualité/prix, utilisable pour un petit satellite home cinéma ou une colonne hifi très mince avec plusieurs unités pour obtenir l'ampleur d'un haut-parleur plus grand.

Specifications :
Overall dimension : D90 x 43.4 mm
Net weight : 0.47 kg
Nominal power handling : 12 W RMS
Nominal impedance : 8 ohm
Sensivity : 85.7 dB/1w/1m
Frequency response : 100 - 25000 Hz
Fs : 125 Hz

Voice coil :
Diameter : 20 mm
Height : 7 mm
Former : Black Aluminium
Wire : Copper round
Number of layers : 2
DC resistance : 6.0 ohm

Magnet system :
Type : Ferrite
Gap height : 3 mm
B Flux density : 1.0 Tesla
Bl product : 3.7 Tm
Max linear excursion : +/- 1.5 mm

T/S parameters :
Cms : 0.82 mm/N
Sd : 27 cm²
VAS : 0.85 L
Mmd : 1.991 gr
Mms : 2.073 gr
Qms : 2.13
Qes : 0.67
Qts : 0.52

Fountek FR88EX

Specifications :
Overall dimension : D88.4 x 52.4 mm
Net weight : 0.35 kg
Nominal power handling : 15 W RMS
Nominal impedance : 8 ohm
Sensivity : 84.3 dB/1w/1m
Frequency response : 90 - 20000 Hz
Fs : 95 Hz

Voice coil :
Diameter : 25 mm
Height : 4 mm
Former : Aluminium
Wire : Copper ribbon
Number of layers : 1
DC resistance : 6.0 ohm

Magnet system :
Type : Neodymium
Gap height : 10 mm
B Flux density : 0.88 Tesla
Bl product : 3.313 Tm
Max linear excursion : +/- 3.0 mm

T/S parameters :
Cms : 1.196 mm/N
Sd : 27.34 cm²
VAS : 1.269 L
Mmd : 2.274 gr
Mms : 2.356 gr
Qms : 1.96
Qes : 0.622
Qts : 0.472

Phonocar 3/009

Type de grille : Couronne de fixation + grille métallique de protection perforée.
Pour la protection des haut-parleurs standards 20 cm (8 pouce). La grille est bombée pour éviter l'enfoncement et laisser la membrane du haut-parleur se déplacer librement.

Produit vendu par paire (grille + couronne), prix affiché pour une paire. (vis de fixation non fournies)

Dimensions couronne
Diamètre extérieur total : 224 mm
Diamètre encastrement hp : 181 mm
Epaisseur couronne : 17 mm

Dimensions grille
Diamètre extérieur total : 216 mm
Epaisseur : 22 mm (bombée)

Profondeur d'encastrement de la grille dans la couronne : ~7 mm

SETA RWS1064 560

Les principales caractéristiques de la série RWS (dissipation élevée, endurance et robustesse mécanique) et lemploi dun émail vitrifié à température élevée assurent des performances répondant aux exigences des utilisateurs de lélectricité et de lélectronique.

Limite de température : -55°C à (to) 400 °C
Coefficient de température : + 95 ppm / °C (valeur typique)

Résistance : 560 Ohm